Back to Blog
How-to Guides 2026-11-01 Matphoto 8 views

Tarpaulin 2x3 on Set: Ground Cover and Equipment Protection

Tarpaulin 2x3 on Set: Ground Cover and Equipment Protection

A practical tarpaulin 2x3 setup guide for photo and video sets: how to protect gear outdoors, cover studio floors, and avoid common tarp mistakes.

Quick answer

Use a tarpaulin 2x3 as a sacrificial ground cover or quick equipment shield, not as a structural waterproof barrier. Lay it flat, secure the edges, and keep gear off the seams to get reliable protection without creating a trip hazard.

When a 2x3 tarp is the right size for set work

A 2x3 tarpaulin covers roughly the footprint of a small tripod cluster, a light stand base, or a single equipment case. It is too small to serve as a full floor cover for a large studio, but it is easy to fold, carry, and reposition between setups.

If you need to protect a larger area, overlap two or more tarps and tape the seams. Do not assume a single 2x3 sheet will keep a whole camera cart dry in heavy rain.

Ground cover versus overhead protection

On a studio floor, a tarp protects against paint, dust, and minor spills. Outdoors, it can shield equipment from damp ground or sudden showers, but it is not a substitute for a proper rain cover or tent. Use it as a base layer under cases and stands, not as a roof.

The BACHE TARPAULIN 2X3 is tagged for light and rental use, which suggests it is intended for temporary setups where quick deployment matters more than heavy-duty weatherproofing.

Step-by-step tarpaulin setup for set use

  1. Inspect the surface and clear debris: Sweep the floor or ground before laying the tarp. Remove stones, cable ends, and sharp objects that could puncture the material. Common mistake: laying a tarp over a cable run and then walking on it, which damages both the cable and the tarp. A clean, flat base makes the tarp last longer and lie flatter.
  2. Unfold and position the tarp: Unfold the 2x3 tarp fully and place it where equipment will sit or where foot traffic crosses. Keep the shiny side up if the material has a coated side, as it usually sheds water better. Common mistake: leaving folds and creases that create trip hazards. Smooth out wrinkles before placing any stands or cases on top.
  3. Secure the edges: Use gaffer tape, sandbags, or weighted cases along the perimeter to keep the tarp from shifting. On smooth studio floors, tape the edges down completely. Common mistake: relying on the tarp's own weight, which fails when someone catches a foot on it. Tape or weight every edge that borders a walking path.
  4. Place equipment and check stability: Set stands, tripods, and cases on the tarp, then test each for wobble. A tarp adds a slight compressible layer, so re-level any stand that feels unstable. Common mistake: assuming a stand that was stable on the bare floor will be stable on the tarp. Re-check stability after the tarp is in place, not before.
  5. Manage water and spills: If water collects on the tarp, lift one edge to drain it away from equipment. Do not let water pool near electrical connections. Common mistake: letting a puddle sit under a light stand, which can seep into the base. Drain or mop up standing water immediately; do not wait for the end of the shoot.
  6. Fold and store after use: Shake off loose dirt, let the tarp dry completely, and fold it loosely rather than tightly creasing it. Store it flat or rolled. Common mistake: folding a damp tarp, which traps moisture and causes mildew. A dry tarp folds smaller and lasts longer; never store it wet.

Product facts

  • BACHE TARPAULIN 2X3: The BACHE TARPAULIN 2X3 is a 2 by 3 format cover from Matphoto, tagged for light and rental use. Its size and rental-friendly tagging make it a practical disposable layer for protecting floors and gear during short shoots.
    BACHE TARPAULIN 2X3
    BACHE TARPAULIN 2X3

Related Articles

Customer Service
Home
Products
Cart
Profile